HELTUN Touch Panel Switch One Buttons Z-Wave Plus

AED 605

HELTUN Touch Panel Switch, 1 channels Z-Wave Plus V2

  • Association control of 100 devices from network
  • Independent control of each relays and LEDs
  • Each relay can be controlled by any touch button or via a Z-Wave network (Z-Wave controller).
  • Each touch button can be configured to control any relay
  • Each touch buttons can be used to run scenarios
  • Software energy consumption meter logic
  • Consumption meter reset
  • Temperature sensors calibration
  • Adjustable backlight brightness: Auto or Manual

Warranty

All HELTUN products come with 3 years extendable warranty

SKU: HE-TPS01-WW Category:

Take Control

The HELTUN Touch Panel Switch is an Advanced Programmable Touch Panel Switch - One Button brings ‘Impossibly Smart’ capabilities to your home lighting or motorized blinds, door locks, gates, and valves. It replaces an existing in-wall switch and brings over-the-Internet monitoring, control, and advanced programmability to five connected devices. Touch Panel is ‘Impossibly Thin’ on the wall yet packed with features to provide the ultimate in control and convenience.

One channel relay with dry contacts & 5 Amp load. HELTUN Advanced Zero-Cross Technology delivers greatly increased longevity & reliability of the system.

Impossibly Thin

Six Ways To Play

The HELTUN Touch Panel Switch comes in six different configurations to fit any need. Whether one switch or five, the HELTUN Touch Panel Switch is still "Impossibly Thin" and "Impossibly Smart".

Internal Sensors

HELTUN Touch Panel Switches include sensors to monitor temperature, humidity, and ambient light which can be accessed by a Z-Wave controller and used to trigger home automation scenes. The frequency (reporting time) of data updates from sensors can be individually adjusted to meet the needs of your smart home system.

Inputs & Outputs

The main power input can be either 85-265VAC or 12-48VDC. There are five relay outputs each with a maximum 5 Amp load. There are also two independent inputs for relay channels that allow control of systems with different power sources, or to use outputs as dry contacts: e.g. to switch On/Off 220VAC lights and control motorized valves with 24VDC power. Input 1 with the required power source is for relay channels 1, 2 and 3, which can carry a maximum 15 Amp load. Input 2 with the required power source is for relay channels 4 and 5, which can carry a maximum 10 Amp load. Each relay channel uses HELTUN Advanced Zero-Cross Technology to deliver greatly increased longevity & reliability of your system.

Know How Much Energy You Use

The HELTUN built-in Power Consumption System precisely monitors how much energy you used during any particular day, week, or month. Do your current light switches do that? Just specify the consumption of the load in watts for each relay channel and the Relay Switch quinto logic will calculate total consumption relative to the time since the output was in the ‘ON’ state. We have also designed the circuitry so it draws almost zero watts to power itself when in standby mode. This saves you energy and money especially if your home is equipped with many HELTUN products.

Motorized Device Controls

The HELTUN Touch Panel Switch does a lot more than just control house lights. You can use it to control motorized blinds, curtains, garage doors, driveway gates, and electric locks. You have full control over programming different buttons for specific functions. For example, you can designate the top left button to raise the living room blinds, and the bottom left button to lower them. In this mode, if the blinds are rising and you then touch the down button, the system will automatically cancel the UP command and initiate a DOWN command, or vice-versa. The system also calculates the position of the blinds when fully opened or closed and automatically stops the motor when it reaches the UP or DOWN limit. If you have installed a door sensor - as on a garage door - you can associate that sensor with the button backlight to indicate the actual UP or DOWN state of the door.

Schedules & Scenarios

Using the internal timekeeping of the HELTUN Touch Panel Switch, you can create schedules for some devices. For example: Open the blinds at 7:00AM and close them at 10:00PM. Switch on the porch light at 7:00PM and turn it off at 1:00AM. Scenarios can also be created that allow connected devices to be triggered by a sensor. For example: If the ambient light sensor detects less then 200 lux, connected house lights would switch to ON. If the internal temperature sensor measured less than 23°C, the connected heating system could be switched on. The possibilities for adding convenience and comfort are endless and limited only by the creativity of the owner or installer of the HELTUN Touch Panel Switch.

Control Up to 100 Z-Wave Devices

The HELTUN Touch Panel Switch one to five buttons(quinto) has 20 association groups, with 5 controlled devices for each group. “Basic Set Devices” (On/Off), or “Multilevel Set Devices” (Variable Position), can be associated to each group. This enables it to operate within the most demanding smart home systems.

Easy Installation

HELTUN Touch Panel Switches can be easily installed into any standard electrical junction box (square or round). Installation must only be performed by someone trained in handling high voltage electrical systems.

Compatibility

Compatible with: Aeotec, ComfortClick, Eedomus, Ezlo, Fibaro HC2, HC3, Jeedom, Home Assistant, Homey, Hubitat, RazBerry, SmartThings, Thinka, Zipato gateways and Z-Wave JS library

Warranty

All HELTUN products come with 3 years extendable warranty

Technical Details

  • Front frame dimensions: 89x89x9mm
  • Back dimensions: 53x53x28mm
  • Material: Flame retardant plastic, tempered glass
  • 4 frame colors: Silver, Chrome, Black, White
  • 6 glass colors: White, Black, Yellow, Green, Red, and Blue
  • 5 sensitive capacitive touch buttons
  • Red and Blue color LED backlight for each button
  • 3 levels of adjustable brightness for backlight
  • Operating temperature: -10°C – +60°C
  • Power supply: 100VAC – 250VAC, 50Hz/60Hz
  • Power consumption: 1.5W
  • 5 relays with resistive load up to 5A each
  • 2 independent relays input, dry contact type
  • Relay lifetime: 100.000 switches
  • Internal ambient brightness sensor
  • Internal temperature sensor
  • Measurement range: -40°C to +125°C
  • Accuracy: ±0.5°C
  • Internal humidity sensor
  • Measurement range: 0 – 80%RH
  • Accuracy: ±3.0%RH
  • IP class: IP21
  • Z-Wave Frequency: All countries
  • Z-Wave SDK: V7.11.1
  • Z-Wave Plus module: ZGM130S